Fabrication Services — Vessel Fabrication
LPG Storage Tank
Spherical and bullet-type pressure vessels engineered to store LPG, LNG, and NGL products safely under pressure — fabricated to ASME Section VIII and NFPA 58/59 with redundant relief protection.
Keeping a liquefied gas liquid until it’s needed
An LPG storage tank holds propane, LNG, or NGL products in liquid form under enough pressure to keep them from vaporizing at ambient temperature. Unlike an atmospheric storage tank, it’s a full pressure vessel — the design pressure is set by the equilibrium vapor pressure of the stored product at its maximum design temperature, not by an arbitrary safety margin. Get that number wrong and either the tank is underdesigned for a hot day, or overbuilt and needlessly expensive.
Fintelius selects spherical or bullet (horizontal cylindrical) geometry against the storage volume and site constraints, then engineers the shell, supports, and dual relief-valve system to NFPA equilibrium-pressure criteria and ASME Code, whether the tank ships aboveground, mounded, or for underground installation.
- Spherical tanks for large-volume storage above roughly 500 m³; bullet tanks for smaller and mid-range volumes
- Aboveground, mounded, and underground installation configurations
- Stainless steel, Hastelloy, Monel, Inconel & Duplex 2205 construction options
- Fabricated to ASME Section VIII Div. I & II and NFPA 58, with dual 100%-capacity relief valves
From equilibrium pressure calculation to a hydrostatically tested tank
Every LPG tank follows the same disciplined path through design and fabrication.
Design Pressure & Temperature Analysis
Stored product’s equilibrium vapor pressure at maximum design temperature (ambient plus solar radiation) sets the governing design pressure.
Geometry & Installation Selection
Spherical or bullet geometry, and aboveground, mounded, or underground installation, are selected against volume and site constraints.
Shell & Head Fabrication
Plate is rolled and formed to the design diameter and wall thickness, welded to spherical or cylindrical shell geometry.
Welding, NDE & PWHT
All welds are radiographed and ultrasonically tested; thick sections undergo post-weld heat treatment per code.
Hydrostatic Testing & Dispatch
The complete tank is hydrostatically tested, coated, and prepared for shipment or field erection with full documentation.
Matched to storage volume & site layout
Spherical Tank
The most economical shell geometry for storage volumes above roughly 500 m³ — a sphere minimizes shell surface area, and therefore material and cost, for a given volume under pressure.
Bullet (Horizontal Cylindrical) Tank
Typically used under 100 m³ and common in the 100–500 m³ range where total weight and installation logistics favor a cylindrical shape over a sphere.
Underground / Mounded Tank
Horizontal configuration by default regardless of capacity — buried or mounded on a concrete platform for space-limited or safety-driven site layouts.
What separates a safe LPG tank from an underdesigned one
These parameters are set by code and equilibrium physics, not estimated.
Equilibrium Design Pressure
Design pressure is set to the stored product’s equilibrium vapor pressure at maximum design temperature — per NFPA, roughly 41°C (underground), 46°C (>4.5 m³), or 54°C (≤4.5 m³).
Dual 100% Relief Valves
Two pressure relief valves, each rated to 100% capacity, are mandated so one can be serviced or isolated without taking the tank out of service.
Excess Flow & Safety Valves
Excess-flow check valves limit release rate in the event of downstream piping failure, working alongside the primary relief system.
Gas Leak Detection
Integrated leak-detection instrumentation for early warning ahead of a release reaching hazardous concentration.
Heating & Cooling Systems
Optional temperature-control systems maintain product state and pressure within design limits across ambient extremes.
Welded Support Design
Legs, lugs, skirts, or saddles engineered for the tank’s geometry, seismic zone, and foundation type.
What a pressurized liquefied-gas vessel demands
Shell & Head Fabrication
Rolled shell and formed heads (or welded spherical segments) to the design diameter and wall thickness.
Nozzle & Manway Fabrication
Fill, withdrawal, vapor equalization, relief, drain, and instrumentation nozzles with reinforcement pads; manways for internal access.
Support Structure Fabrication
Legs, lugs, skirts, or saddles fabricated and welded to the vessel per site foundation and orientation requirements.
Advanced Coating Systems
Protective coating options for above-ground weathering resistance and, where specified, corrosion protection for buried installations.
Post-Weld Heat Treatment
Stress-relief heat treatment for thick-walled shell and head sections per ASME code requirements.
Radiography & Ultrasonic NDE
Weld integrity verification across all shell, head, and nozzle welds before hydrostatic test.
Hydrostatic Test Rigs
Full-vessel pressure testing to design specification prior to dispatch.
Instrumentation Integration
Level, pressure, and temperature instrumentation supporting safe operation and inventory management.
NFPA 58 Code Compliance
Fabrication and safety features engineered to the NFPA 58 stationary LPG storage code alongside ASME pressure vessel requirements.
Capability at a glance
Where our LPG storage tanks go to work
Oil & Gas Production
Bulk LPG and NGL storage at production, gathering, and processing facilities.
Petrochemical & Chemical Processing
Feedstock and product storage for downstream petrochemical and chemical manufacturing operations.
Power Generation
Fuel storage supporting LPG and NGL-fired power generation facilities.
Marine & Terminal Storage
Bulk storage supporting marine terminal loading, unloading, and distribution operations.
Distribution & Bottling
Bulk storage feeding downstream cylinder-filling and distribution operations.
Industrial & Residential Bulk Supply
Aboveground and underground tanks serving industrial facilities and residential bulk propane supply.

